|
|
|
|
|
|
Welcome to the Australian Ford Forums forum. You are currently viewing our boards as a guest which gives you limited access to view most discussions and inserts advertising. By joining our free community you will have access to post topics, communicate privately with other members, respond to polls, upload content and access many other special features without post based advertising banners. Registration is simple and absolutely free so please, join our community today! If you have any problems with the registration process or your account login, please contact us. Please Note: All new registrations go through a manual approval queue to keep spammers out. This is checked twice each day so there will be a delay before your registration is activated. |
|
|||||||
| The Pub For General Automotive Related Talk |
 |
|
|
Thread Tools | Display Modes |
13-11-2013, 03:53 PM
|
#1 | ||
|
Starter Motor
Join Date: Feb 2012
Posts: 15
|
Hi,
My fibreglass bumper has a crack in it about 5cm long, i need to get it fixed. Does anyone know of a place that repairs fibreglass bumpers? thanks |
||
|
|
|
13-11-2013, 04:00 PM
|
#2 | ||
|
FF.Com.Au Hardcore
Join Date: Sep 2008
Posts: 684
|
have a crack yourself bunnings sell a fiberglass repair kit, read the instructions and away you go. Obviously it will need to be painted, so any panel shop could fix it for you and paint. With fiberglass bumpers I like to crack them as much as I can stand it then buy a new bumper, why pay to have a repaired bumper painted when its easier and cheaper to have a new one painted.
What car and what bar? |
||
|
|
|
|
13-11-2013, 04:03 PM
|
#3 | |||
|
Where to next??
Join Date: Oct 2006
Location: Sydney
Posts: 8,893
|
Quote:
Is the crack due to a one off impact or has it built up and extended over time? There may be certain stresses and strains that hone in on that area and if that is the case you will need to remove the bumper and try and strongly re-enforce the back to not allow the crack to re-develop.
__________________
___________________________ I've been around the world a couple of times or maybe more....... |
|||
|
|
|
|
13-11-2013, 04:07 PM
|
#4 | ||
|
Starter Motor
Join Date: Feb 2012
Posts: 15
|
Im in Sydney. Car is AU2 Ute, TS50 Bumper. Damage was due to one a one off occurrence.
|
||
|
|
|
|
13-11-2013, 04:21 PM
|
#5 | ||
|
FF.Com.Au Hardcore
Join Date: Sep 2008
Posts: 684
|
http://www.ebay.com.au/itm/Tickford-...a525c59&_uhb=1
like this for $280 I would get and new bumper unless you use the repair kit any panel shop is going to charge you that to repair |
||
|
|
|
| This user likes this post: |
|
13-11-2013, 05:23 PM
|
#6 | ||
|
FF.Com.Au Hardcore
Join Date: Oct 2008
Location: Victoria
Posts: 7,854
|
Bargain, take a piece of your old one off to colour match and get it painted before fitting.
__________________
______________________________ 2015 Territory Titanium RWD Diesel - SOLD 2016 BMW X5 xdrive 30D Msport Seadoo Challenger 210SE 310HP |
||
|
|
|
|
15-11-2013, 12:22 PM
|
#7 | ||
|
FF.Com.Au Hardcore
Join Date: Feb 2005
Location: Melb north
Posts: 12,025
|
I would think any beater could fix it, they will just grind out the crack and load it up mat and resin and sand it up when it goes hard, then the usual process of touching up with fillers and paint.
|
||
|
|
|
Need to Repair Fibre Glass Bumper
Linear Mode
